NEO TOOLS UK · CUSTOMER INFORMATION

Hints & Tips | Glove & Workwear Sizing, PPE Guides – NEO Tools

NEO TOOLS | CUSTOMER HELP CENTRE

Hints, Tips & Size Guides

Helpful explanations, product advice and practical sizing guides for workwear and PPE.

GUIDE 01 — HAND PROTECTION

Find your glove size

Properly fitting gloves can help with comfort and dexterity. To measure, use a soft tape around the widest part of your dominant hand just below the knuckles, excluding the thumb.

Illustrated NEO Tools glove measuring guide showing the tape wrapped around the palm below the knuckles
  1. Open your hand naturally with fingers together.
  2. Wrap the tape around your palm just below the knuckles, leaving out the thumb.
  3. Read the hand circumference in centimetres and check the sizing information for your chosen glove.
  4. If between sizes, assess whether the intended task needs closer dexterity or more room. Try the glove on where possible.

Important: The S–XXL measurements in the illustration are illustrative only, not a verified fit chart for every NEO glove. Individual models can use numbered sizes 6–11 and have their own fit charts. Always check the product's manufacturer size information.

Browse workwear & PPE

GUIDE 02 — WORKWEAR FIT

Workwear & clothing size guide

Use a tape measure while standing upright, keeping it level and comfortably snug. The reference ranges below are taken from the NEO clothing size chart, organised by clothing range. All body measurements are in centimetres.

UK and EU sizes: Both are shown in the table headers. Women’s UK dress-size equivalents and men’s approximate UK chest-inch equivalents are guides only; workwear sizing can vary by range and garment cut. Measure your body using the centimetre measurements in the table before ordering. For men’s sizes, “UK 40″ chest” means a nominal 40-inch chest size, not a guaranteed body measurement.
NEO Tools illustrated workwear size guide with chest waist hip and height measurement diagram and clothing range tables
Where to measure

A: around the fullest part of the chest or bust. B: around the waist. C: around the fullest part of the hips when specified; for the HD/Cotton/Basic and Warm/Outdoor/Visibility tables, C denotes height. D: standing height where shown. The labels depend on the range—follow each table.

Scroll horizontally on mobile to see every size column. Check the specific garment range and product listing before selecting a size.

Women's workwear

Measurement (cm) S (34)UK 6 S (36)UK 8 M (38)UK 10 L (40)UK 12 XL (42)UK 14 XXL (44)UK 16 XXXL (46)UK 18
Chest / bust (A) 80–84 84–88 88–92 92–96 96–102 102–108 102–108
Waist (B) 62–66 66–70 70–74 74–78 78–84 84–90 84–90
Hips (C) 88–92 92–96 96–100 100–104 104–108 108–112 108–112
Height (D) 162–165 165–168 168–171 171–174 174–177 180–183 180–183

Premium / Mix & Match / Denim / Camo / Navy / HD+ / HD Slim / Cotton Slim / Comfort

Measurement (cm) XS (46)UK 36″ chest S (48)UK 38″ chest M (50)UK 40″ chest L (52)UK 42″ chest XL (54)UK 44″ chest XXL (56)UK 46″ chest XXXL (58)UK 48″ chest
Chest (A) 91–95 95–99 99–103 103–107 107–111 111–115 115–119
Waist (B) 78–82 82–86 86–90 90–94 94–98 98–102 102–106
Hips (C) 90–94 94–98 98–102 102–106 106–110 110–114 114–118
Height (D) 172–175 175–178 178–181 181–184 184–187 187–190 190–193

HD / Cotton / Basic

Measurement (cm) S (48)UK 38″ chest M (50)UK 40″ chest L (52)UK 42″ chest LD (54)UK 44″ chest XL (56)UK 46″ chest XXL (58)UK 48″ chest
Chest (A) 92–96 96–104 104–108 108–116 116–124 124–132
Waist (B) 64–72 72–80 80–88 88–96 96–104 104–112
Height (C) 164–170 170–176 176–182 182–188 188–194 194–200

Warm / Outdoor / Visibility

Measurement (cm) S (48)UK 38″ chest M (50)UK 40″ chest L (52)UK 42″ chest XL (56)UK 46″ chest XXL (58)UK 48″ chest XXXL (60)UK 50″ chest
Chest (A) 94–100 100–108 108–116 116–124 124–130 130–136
Waist (B) 82–88 88–94 94–100 100–106 106–112 112–118
Height (C) 164–172 172–180 180–188 188–194 194–200 194–200

Thermal underwear

Measurement (cm) S/M (48/50)UK 38″ chest / UK 40″ chest L/XL (52/54)UK 42″ chest / UK 44″ chest XXL/XXXL (56/58)UK 46″ chest / UK 48″ chest
Chest (A) 95–103 103–111 111–119
Waist (B) 82–90 90–98 98–106
Hips (C) 94–102 102–110 110–118
Height (D) 175–181 181–187 187–193

NEO tip: If you're between sizes, check the intended layers of clothing and whether you need extra movement. Different ranges have different measurements even when the letter size is the same.

GUIDE 03 — BREATHING PROTECTION

Choosing masks and respiratory protection

Respiratory protective equipment (RPE) should be selected following a hazard-specific workplace risk assessment. Selection depends on what is in the air, exposure levels, the required protection factor and the actual certified product performance.

Type / situation What to know
FFP1 Particulate protection class; suitability depends on the risk assessment and assigned protection factor.
FFP2 Higher particulate filtering class than FFP1, but not a universal solution for all dust or fumes.
FFP3 Higher particulate filtering class; often considered for more demanding particulate hazards where assessed as suitable.
Paint vapours / solvent gases Particulate-only disposable masks do not provide the necessary gas/vapour protection. Specialist selection is required.
Oxygen-deficient / unknown atmosphere Do not use a filtering mask; specialist safety procedures and appropriate breathing apparatus are needed.

Fit matters: Tight-fitting masks require suitable face-fit testing and a pre-use seal check. Facial hair can prevent an adequate seal. Follow product instructions and employer procedures.

Official references: HSE fit testing guidance and HSE RPE selection guide (HSG53).

GUIDE 04 — QUICK PRODUCT EXPLANATIONS

What are NEO pencil refills?

The following products are replacement leads, not complete pencils. Use the matching pencil model when ordering.

SKU Description Compatible pencils
13-820 White HB leads, pack of 5 13-810 / 13-815
13-821 Black HB leads, pack of 5 13-810 / 13-815
13-822 Black 2H leads, pack of 5 13-810 / 13-815
13-823 Black HB leads, pack of 6 13-816

Shop NEO marking pencils and refills

GUIDE 05 — TOOL BUYING

Drills, drivers and impact wrenches explained

Drill/driver: general screwdriving and drilling in suitable materials. Hammer drill: adds percussion for suitable masonry. Impact driver: repeated rotational impacts for compatible fasteners. Impact wrench: uses square-drive impact sockets for fastening tasks demanding higher torque.

Understanding drive sizes

Common square drives include 1/4, 3/8 and 1/2 inch. Use suitable impact-rated sockets with an impact tool and check the manufacturer's limits.

Torque explained

Torque is rotational force, normally specified in Nm. Use manufacturer tightening specifications and a suitable torque wrench when precise tightening is required.

Compare tool specifications →

GUIDE 06 — CORDLESS TOOLS

GRAPHITE Energy+ batteries and chargers

Voltage indicates the electrical battery platform. Amp-hours (Ah) describe nominal charge capacity; a higher Ah rating may provide longer runtime in similar conditions, but actual runtime depends on the tool and task.

  1. Check the exact model and manufacturer's compatible battery platform.
  2. Confirm the charger supports that battery.
  3. Check whether the tool is sold body-only or includes a battery and charger.
  4. Follow manufacturer guidance for safe charging and storage; never use a damaged battery.

Browse GRAPHITE Energy+ tools, batteries and chargers →

GUIDE 07 — ORDERING

Before you order

  • Check the product model, size and intended application.
  • For cordless tools, verify battery and charger compatibility and what's included.
  • For PPE, follow manufacturer certification, selection and fit instructions.
  • Check the product's availability, pre-order status and the delivery policy.
  • Buying multiple items? Ask our UK team for a bulk or trade quotation.

NEED HELP?

We're here to help you choose

Have a question about sizing, an unusual product code or protective equipment? Tell us the item number and what you need it for.

01782 901325   |   hello@cenvixogroup.com

General buyer guidance only. This does not replace current manufacturer instructions, a workplace risk assessment, face-fit testing, PPE certification or specialist health and safety advice.

NEO TOOLS

Orders open 9 December

–Days
–Hours
–Minutes
–Seconds
Yellow Renault 5 Turbo on the rally track Alitalia-liveried Lancia Stratos at Rally Village